Up for sale is a 1970s TEAC Tascam Series Model 5A, an 8-channel, 4-bus modular analog recording console prized for its Tamura transformers, warm vintage overdrive, and flexible studio routing.
Service, Restoration & Bench Testing
* Power Section Recap: Full recap of the power section and filter capacitors using premium Vishay and Sprague components.
* Installed new 15V voltage regulators, fresh thermal compound, and new mica insulators to ensure cool, reliable operation and steady voltage rails.
* Meter Illumination: Replaced VU meter lamps with factory-spec 8V 100mA incandescent bulbs.
* Authentic OEM Restoration: Restored faulty components using original OEM donor parts, including two DP3T Vishay switches on channel inputs 6 and 8.
* Factory-Spec Bench Diagnostic & Alignment: Put through a comprehensive, step-by-step diagnostic following the official factory service manual. Every channel strip, bus, and internal component has been verified with zero faults found, with input modules and gain staging aligned for absolute accuracy at 0 VU (0 dB = 1V).
* Internal Control Cleaning: All switches, buttons, potentiometers, and faders across the input and summing modules have been thoroughly cleaned and treated with electronics contact cleaner, DeoxIT, and fader lube.
* I/O Jack Maintenance: All inputs and outputs on the rear panel have been meticulously cleaned and verified fully operational.
* Cosmetic Care: Given a full exterior, faceplate, and knob cleaning for a sharp, studio-ready appearance.
Overview & Studio Workflow
Built as the centerpiece for multitrack tape recording, overdubbing, and mixdown, the Model 5A fits seamlessly into both classic reel-to-reel rigs and modern hybrid DAW studios. Each of the eight removable channel modules offers transformer-balanced XLR mic preamps, a two-band selectable EQ, pan, solo, and fader controls, routing into four output buses monitored by four large analog VU meters.
As the updated 5A revision, this console resolves key workflow limitations of the original Model 5—adding a dedicated front-panel headphone amplifier (separated from the Studio Feed circuit) and refined direct-out switching. This makes it an ideal 8-channel vintage front-end preamp or analog summing desk for tracking straight into a digital interface.
Technical Specifications
* Architecture & Modules: 8 Input Channels (Mic / Line / Tape switchable) x 4 Output Buses. Built with removable Model 201 Input Modules, Model 202 Submaster Modules, and a Model 203A Master/Monitor Module.
* I/O & Routing: Balanced XLR mic inputs (no built-in +48V phantom power), unbalanced RCA line/tape/insert jacks (-10 dBV), individual channel direct outs, Cue & Echo aux sends, and 1/4" headphone/monitor outputs.
* Equalization (Per Channel): Two-band EQ with ±15 dB continuously variable boost/cut. High band switchable between 3 kHz and 10 kHz; low band switchable between 75 Hz and 200 Hz.
* Frequency Response: 30 Hz to 20 kHz (±2 dB)
* Total Harmonic Distortion (THD): 0.1% maximum overall (mic input to output)
* Signal-to-Noise Ratio: > 75 dB weighted (70 dB unweighted) with 1 input active; > 65 dB weighted (60 dB unweighted) with all 8 inputs active
* Equivalent Input Noise (EIN): -125 dB
* Crosstalk & Fader Attenuation: > 60 dB at 1 kHz / > 60 dB fader attenuation
* Output Levels: Main Line & Monitor outputs at -2 dB nominal / +18 dB maximum (> 10K ohms load). Direct Outs & Aux/Tape I/O at -10 dB nominal (> 10K ohms load). Model 5A dedicated headphone output rated at 100 mW into > 8 ohms.
* Power Requirements: 117V AC (configurable for 200V/220V/240V), 50/60 Hz, 40W
* Dimensions & Weight: 23 1/8" W x 7 1/2" H x 24 1/2" D | Approx. 62 lbs