I have a 12V DC Generator I built using a Mike's Windmill Shop Quick Charge PMA (permanent magnet alternator) and am electric start Honda Engine (5HP). This has never been used, the engine has never had oil in the crankcase, never been started and the PMA has never been used. The entire generator is mounted on a thick steel plate which altogether is very heavy.
The starting battery shown in the pictures is bad. I can attach another battery to show that the electric start works. The wagon is not for sale.
I designed and built this to charge my battery pack when there was not enough sun in the winter.
I never used it because I moved and no longer lived off grid.
If you need more information about the Quick Charge PMA, visit http://www.mikeswindmillshop.com/ they are located in Show Low, AZ
Ipdated:
I checked and they are now out of business. However their design is used by any PMA that is similar. I have rounded up some information on the Quick Charge PMA and if you compare anyone else product they will probably be exactly the same as most of the people learned from Mike Goss and then started their own business.
TECHNICAL SPECIFICATION SHEET: QUICK CHARGE PMA (ENGINE-DRIVEN) V2 Manufacturer / Origin: Mike's Windmill Shop (Show Low, AZ)
Product Line: Quick Charge PMA (Engine / Belt-Driven Series)
Primary Application: Engine-Powered High-Output Battery Charging Systems (Gas/Diesel Gen-Set) ================================================================================SYSTEM OVERVIEW
================================================================================
The Quick Charge PMA is a belt- or direct-driven permanent magnet alternator designed specifically to pair with small internal combustion engines (3.5 HP to 6.5 HP+) for rapid off-grid battery charging. By incorporating high-flux Neodymium permanent magnets instead of a conventional field coil, the generator requires zero battery power for field excitation and delivers immediate, full-amperage bulk charging from the moment the engine reaches operating speed. ================================================================================
2. MECHANICAL SPECIFICATIONS• Base Housing Chassis: Remanufactured Heavy-Duty GM / Delco (10DN / 10SI series standard frame)
• Drive Type: Pulley / Belt-driven (V-belt or Serpentine) off horizontal-shaft small engine
• Rotor Assembly: Custom precision-machined rotor fitted with high-flux Neodymium (NdFeB) Rare Earth magnets
• Stator Configuration: Hand-wound stator core optimized for 2,000 - 3,500 RPM shaft speeds
• Bearings: High-speed dual sealed precision ball bearings
• Mounting Pattern: Standard Delco single/dual-foot pivot ear mounting for universal bracket alignment
• Cooling: External bi-directional fan blade assembly integrated into pulley hub ================================================================================
3. ELECTRICAL OUTPUT & PERFORMANCE RATINGS[ 12V Engine-Driven System Rating ]
• Output Voltage Type: Wild 3-Phase AC (requires external bridge rectifier)
• Nominal System Voltage: 12 VDC Nominal (14.2V - 14.6V bulk charge cutoff threshold)
• Continuous Current Output: 40 Amps DC
• Continuous Power Rating: ~560 W - 600 W Continuous
• Operating Shaft RPM: 2,500 - 3,600 RPM (achieved via engine pulley step-up ratio)
• Field Excitation Power: 0 Watts (Self-exciting via Neodymium permanent magnets) ================================================================================
4. SYSTEM ELECTRICAL REQUIREMENTS & INTERFACE SPECIFICATIONS4.1. Rectification
• Requirement: External 3-Phase Bridge Rectifier required (minimum 50A / 600V rated module).
• Input Leads: 3-wire wild AC connection from PMA to rectifier input terminals (phase order arbitrary).
• DC Output: Filtered DC output routed directly to battery bank via heavy copper cabling. 4.2. Circuit Protection & Cabling
• Wiring Gauge: Minimum 8 AWG (6 AWG recommended for runs over 10 ft) high-strand copper wire from rectifier DC output to battery terminals.
• Circuit Protection: Heavy-duty inline 50A DC fuse or magnetic circuit breaker placed on the positive line near the battery bank.
• Voltage Regulation / Throttle: Engine speed/throttle adjustment or automatic engine shutdown controls charge termination when bulk battery voltage reaches capacity. ================================================================================
5. ENVIRONMENTAL & OPERATIONAL CONSTRAINTS• Operating Duty Cycle: Continuous output under active mechanical engine load• Thermal Limit: Stator insulation rated for Class B/F operational temperatures (< 130°C / 266°F)• No-Load Operations: PROHIBITED. Never operate PMA open-circuit at high engine RPM without a connected battery bank; uncontrolled open-circuit voltages can exceed terminal insulation ratings and damage the rectifier diodes.